~ PAGE 5 ~

FC-Series

Bearing Number	A Dimension	A1 Dimension	B Dimension	C Dimension	D Dimension	E Dimension	Bore *	Load Rating
FC-2280-10H	2.280	2.250	23/32	15/32	1-3/16	2-7/16	5/8" Hex	425#
FC-2280-11H	2.280	2.250	23/32	15/32	1-3/16	2-7/16	11/16" Hex	425#
FC-2280-11HV	2.280	2.250	23/32	7/32	15/16	2-7/16	11/16" Hex	425#
MFC-2280-7H	2.280	2.250	23/32	15/32	1-3/16	2-7/16	7/16" Hex	425#
MFC-2280-7HV	2.280	2.250	23/32	7/32	15/16	2-7/16	7/16" Hex	425#
MFC-2280-8V	2.280	2.250	23/32	7/32	15/16	2-7/16	1/2" Round	425#
MFC-2280-10	2.280	2.250	23/32	15/32	1-3/16	2-7/16	5/8" Round	425#
MFC-2280-10V	2.280	2.250	23/32	7/32	15/16	2-7/16	5/8" Round	425#
MFC-2280-10H	2.280	2.250	23/32	15/32	1-3/16	2-7/16	5/8" Hex	425#
MFC-2280-10HV	2.280	2.250	23/32	7/32	15/16	2-7/16	5/8" Hex	425#
MFC-2280-11H	2.280	2.250	23/32	15/32	1-3/16	2-7/16	11/16" Hex	425#
MFC-2280-11HV	2.280	2.250	23/32	7/32	15/16	2-7/16	11/16" Hex	425#
MFC-2280-12	2.280	2.250	23/32	15/32	1-3/16	2-7/16	3/4" Round	425#
MFC-2280-12V	2.280	2.250	23/32	7/32	15/16	2-7/16	3/4" Round	425#
MFC-2280-12H	2.280	2.250	23/32	15/32	1-3/16	2-7/16	3/4" Hex	425#
MFC-2280-12HV	2.280	2.250	23/32	7/32	15/16	2-7/16	3/4" Hex	425#

*DUE TO NORMAL WEAR; IT IS BEST TO MEASURE SHAFT SIZE WHEN DETERMINING BORE DIMENSION

A and A1 Dimension tolerances = +0.010/-0.000

FEATURES:

	The above bearings have 13- 3/8" Diameter balls.
	The patented rib feature allows the bearing to be pressed into the 2 ½ " 11 gauge roll without any secondary operation.
	FC at the beginning of the part number designates a plastic insert which acts to quiet the bearing, also allowing it to be re-greased.
	*MFC* designates an all metal inner race.
	S added to the end of the part number, designates a felt seal added to the front of the bearing.
	T added to the end of the part number, designates a Teflon seal added to the front of the bearing.
	All of the above bearings are also available with a non-ribbed case which has a 2.265 A dimension. Substitute 2280 with 2265 in the part number to specify this feature.